Chat with us, powered by LiveChat Should build a a ball track with 4-holes minimum, where the ball should finish the track from start to finish without falling in any holes. Need a 3D design drawing in solidworks wit - Writeedu

Should build a a ball track with 4-holes minimum, where the ball should finish the track from start to finish without falling in any holes. Need a 3D design drawing in solidworks wit

 Should build a a ball track with 4-holes minimum, where the ball should finish the track from start to finish without falling in any holes. Need a 3D design drawing in solidworks with the dimensions in mm, and assembly. All further instructions, and details can be found in the attached file. Please I need this ASAP. 

15FMCE224 – Project Based Learning

Pinball Track

Introduction

Engineering graduates are expected to have strong technical skills and be problem solvers as well

as having good team and communication skills. Engineers are also expected to be creative and

innovative. They have to work with many constraints, while developing safe products and

solutions to help the community.

Project description

You have been hired to design and build a loaded pinball track where the ball would climb up the

track and return safely without falling in any of the holes. A loaded pinball track is a balance

between safety and speed. If the ball would fall in any of the holes on the track, the ball would

fail to finish the race. You will design, construct, and test the pinball track with the following

constraints:

Design Requirements:

 The maximum track dimensions are 1.5m x 1.5m x 1.5m

 The maximum track width is 0.15m

 The track must have minimum of 4 holes

 The diameter of each hole must be 10% bigger than the diameter of the ball

 The ball must climb up the track and come down in opposite direction without falling in

any of the holes

 The slope angle of the initial and final ramp has to be at least 30 degrees from the

horizontal surface (floor)

 There must be at least 0.2m of flat surface between initial and final ramp

 The object must stop without jumping, between 0.6m to 0.8m away from the end of the

final ramp on the workshop floor, without using added barriers

 Any mechanism can be used to push the ball but it has to be automatic without direct use

of hand

General Requirements:

 You will be working in a group of four or five and you will remain in these groups for the

entirety of the project. You may not combine or switch groups.

 Each team member is supposed to come up with one idea.

 Analyze all team designs and refine your ideas down to one using a decision matrix.

 Your team needs to discuss advantages and disadvantages of each design idea.

 Analyze your design using hand calculations or software. However, the report including

the calculations has to be typed; using Times New Roman /12 for the body of the report.

 All design work must be using a 3-D modeling software such as SOLIDWORKS.

 Show all your design assumptions in your technical report.

 The pinball track must be designed so that the movement of the object is stable and

smooth and the whole operation is accurate and safe.

 It is expected that you perform the design and build it to validate your calculations.

 It is required that you calculate the required pushing force, speed, power, distance and

any other required parameter.

 Feel free to use springs, rubber bands or any other mechanical or electromechanical

devices to store sufficient energy that can be converted to kinetic energy to achieve the

required design.

 Feel free to use any types of materials for either the track or the ball.

 You can use any mechanism to control the speed and friction on the track ONLY.

 All work has to be carried out on-campus and if there is an operation which cannot be

done in the campus, it has to be agreed and signed by your instructor and Mr. Robin.

 Use of PPE is mandatory while working on constructing the design.

 Using workshop machines is only allowed under supervision of workshop staff.

 This is a team work. All team members are responsible for the produced prototype.

Our website has a team of professional writers who can help you write any of your homework. They will write your papers from scratch. We also have a team of editors just to make sure all papers are of HIGH QUALITY & PLAGIARISM FREE. To make an Order you only need to click Ask A Question and we will direct you to our Order Page at WriteEdu. Then fill Our Order Form with all your assignment instructions. Select your deadline and pay for your paper. You will get it few hours before your set deadline.

Fill in all the assignment paper details that are required in the order form with the standard information being the page count, deadline, academic level and type of paper. It is advisable to have this information at hand so that you can quickly fill in the necessary information needed in the form for the essay writer to be immediately assigned to your writing project. Make payment for the custom essay order to enable us to assign a suitable writer to your order. Payments are made through Paypal on a secured billing page. Finally, sit back and relax.

Do you need an answer to this or any other questions?

Do you need help with this question?

Get assignment help from WriteEdu.com Paper Writing Website and forget about your problems.

WriteEdu provides custom & cheap essay writing 100% original, plagiarism free essays, assignments & dissertations.

With an exceptional team of professional academic experts in a wide range of subjects, we can guarantee you an unrivaled quality of custom-written papers.

Chat with us today! We are always waiting to answer all your questions.

Click here to Place your Order Now